Bulbs
Flower Basics
Flower Beds & Specialty Gardens
Flower Garden
Garden Furniture
Garden Gnomes
Garden Seeds
Garden Sheds
Garden Statues
Garden Tools & Supplies
Gardening Basics
Green & Organic
Groundcovers & Vines
Growing Annuals
Growing Basil
Growing Beans
Growing Berries
Growing Blueberries
Growing Cactus
Growing Corn
Growing Cotton
Growing Edibles
Growing Flowers
Growing Garlic
Growing Grapes
Growing Grass
Growing Herbs
Growing Jasmine
Growing Mint
Growing Mushrooms
Orchids
Growing Peanuts
Growing Perennials
Growing Plants
Growing Rosemary
Growing Roses
Growing Strawberries
Growing Sunflowers
Growing Thyme
Growing Tomatoes
Growing Tulips
Growing Vegetables
Herb Basics
Herb Garden
Indoor Growing
Landscaping Basics
Landscaping Patios
Landscaping Plants
Landscaping Shrubs
Landscaping Trees
Landscaping Walks & Pathways
Lawn Basics
Lawn Maintenance
Lawn Mowers
Lawn Ornaments
Lawn Planting
Lawn Tools
Outdoor Growing
Overall Landscape Planning
Pests, Weeds & Problems
Plant Basics
Rock Garden
Rose Garden
Shrubs
Soil
Specialty Gardens
Trees
Vegetable Garden
Yard Maintenance
How to Build Forms for Concrete Flowerbed Edging
How to Build Forms for Concrete Flowerbed Edging. A concrete curbing around plant beds creates a solid line of defense, creating a barrier between the plant areas and creeping grass. Durable concrete is also longer lasting than some other options, making the time and effort of installation well worth it over the years. To create the curb edge, you...
A concrete curbing around plant beds creates a solid line of defense, creating a barrier between the plant areas and creeping grass. Durable concrete is also longer lasting than some other options, making the time and effort of installation well worth it over the years. To create the curb edge, you need to build a frame to hold the cement in place until it cures. This is accomplished with lumber and a little on-site construction.
Things You'll Need
Flat-edge shovel
1/2-inch-thick plywood
Measuring tape
Power saw
Gravel
Tamping tool
Wood stakes
Hammer
Drill
1/2-inch screws
Cement mix
Wheelbarrow
Trowel
Dig a trench 5 inches wide and 8 inches deep along your plant borders. Use a flat-blade shovel to create straight walls along the inside of the trench.
Cut a 1/2-inch-thick sheet(s) of plywood into strips 12 inches wide, using a power saw. Measure and mark the wood clearly before cutting to ensure even cuts.
Line the insides of the trench with the plywood strips, pressing them to the vertical wall. They should stick above the ground 4 inches.
Fill the trench with 4 inches of gravel and tamp down with a hand-tamping tool. The gravel will provide a sturdy base for your concrete and also help keep the plywood pressed against the sides of the trench.
Tap wood stakes into the ground along the outside of the plywood to prevent them from bowing out once the concrete is poured. From inside the trench, drill 1-inch screws through the plywood and into the stakes to force the boards against the dirt walls.
Mix cement and water in a wheelbarrow, following the package directions. Mix until you get a consistency similar to a thick milkshake. Pour the cement mix into the concrete form to fill the trench to the top of the plywood strips. Smooth the surface of the cement with a masonry trowel to even out after pouring.
Remove the plywood once the concrete has cured. Fill in the edges with dirt, and gently press it in along the sides with your foot to close the gap.
Tips & Warnings
If you have curved landscape edges, 1/4-inch plywood works better, bending to mold to the curves more easily.
To add decorative stamp patterns to the top of your concrete border, wait until the cement dries to a stiff, yet still moldable consistency. If you press the cement and it forms a small puddle, it's still too wet for stamping.
