Bulbs Flower Basics Flower Beds & Specialty Gardens Flower Garden Garden Furniture Garden Gnomes Garden Seeds Garden Sheds Garden Statues Garden Tools & Supplies Gardening Basics Green & Organic Groundcovers & Vines Growing Annuals Growing Basil Growing Beans Growing Berries Growing Blueberries Growing Cactus Growing Corn Growing Cotton Growing Edibles Growing Flowers Growing Garlic Growing Grapes Growing Grass Growing Herbs Growing Jasmine Growing Mint Growing Mushrooms Orchids Growing Peanuts Growing Perennials Growing Plants Growing Rosemary Growing Roses Growing Strawberries Growing Sunflowers Growing Thyme Growing Tomatoes Growing Tulips Growing Vegetables Herb Basics Herb Garden Indoor Growing Landscaping Basics Landscaping Patios Landscaping Plants Landscaping Shrubs Landscaping Trees Landscaping Walks & Pathways Lawn Basics Lawn Maintenance Lawn Mowers Lawn Ornaments Lawn Planting Lawn Tools Outdoor Growing Overall Landscape Planning Pests, Weeds & Problems Plant Basics Rock Garden Rose Garden Shrubs Soil Specialty Gardens Trees Vegetable Garden Yard Maintenance

How to Build an Arbor

How to Start Lemon Seeds Indoors - watch on youtube
How to Build an Arbor

How to Build an Arbor. An arbor can be a beautiful addition to a garden or backyard setting. They are a simple construction project that can be completed in an afternoon and enjoyed for a lifetime.

An arbor can be a beautiful addition to a garden or backyard setting. They are a simple construction project that can be completed in an afternoon and enjoyed for a lifetime.
Things You'll Need
2' x 2' lumber
Tape Measure
Pencil
Saw
Drill
Screws
Material selection
Choose a construction material to fit your style and budget.
Try one of the following 2' x 2' dimensional lumber: Redwood ' a traditional but fairly costly outdoor project building material. CCA treated lumber ' this is common spruce, pine or fur lumber that has undergone a treatment with cyanide salt that makes it highly insect and rot resistant.
Working with less weather resistant wood is an option but care must be take to apply a proper weatherproofing finish.
Choose 11 pieces of 2'x 2' lumber that are straight and true in 10-foot lengths.
Code your pieces with penciled on letters labels as they are cut to make them easy to identify.
Cut and mark them as follows:
A ' 4 pieces, 72 inches long (Roof Trusses)
B ' 4 pieces, 120 inches long (Posts)
C - 7 pieces, 14 inches long (Short Struts)
D ' 2 pieces, 60 inches (Long Struts)
Miter cut one end of each 'A' piece (Roof Truss) at a 60-degree angle to form the roof peak.
Assembly of the Arbor
Assemble as follows using 2 and 1/2 inch long weatherized wood screws. Be sure to pre-drill all screw holes to avoid splitting the relatively narrow gage lumber.
Lay out 2 of the 'B' pieces (Posts) parallel to each other with 3 of the 'C' pieces (Short Struts) between them on the horizontal. They should be spaced as follows: Flush with the top corners of the posts, at three feet below the top corners and at six feet below the top corners. Attach by running screws through the posts and into the ends of the struts. You will now have what looks like a ladder with widely spaced rungs.
Repeat the step above. You know have both side support units assembled. Turn both up on edge 60 inches apart approximately.
Place one 'D' piece (Long Strut) between the two top corners of the side supports. Attach by running screws through the posts and into the end of the long struts.
Repeat the above step for the other side.
Place the angle cut ends of two of the 'A' pieces (Roof trusses) together so that they form a peak. Connect with screws
Repeat the above step. You now have the two completed roof trusses.
Attach these to the top corners of the structure making sure that they are centered (leave an equal amount of roof truss over hang on each side of the structure).
Place the last 'C' piece (Short Strut) between the two roof trusses at the peak to form the ridge, which adds strength and support.
Stand the Arbor upright and put it in position where it will be used. Mark the ground where each post is situated. Move the Arbor to the side and dig your holes for the posts. These holes will be approximately 36 inches deep. Set the posts into the holes and make sure the Arbor is level and square by taking more dirt out or back filling as needed.
Fill the postholes with dirt tamped tightly into the holes. The Arbor is now ready to be decorated or have plants added at the base.
Tips & Warnings
The dimensions of the Arbor can be easily changed to fit larger or smaller yard or garden areas.
The arbor can also be covered with decorative wire or wood lattice work to give a more closed in look or give vines more of a climbing foothold.

Check out these related posts