Bulbs
Flower Basics
Flower Beds & Specialty Gardens
Flower Garden
Garden Furniture
Garden Gnomes
Garden Seeds
Garden Sheds
Garden Statues
Garden Tools & Supplies
Gardening Basics
Green & Organic
Groundcovers & Vines
Growing Annuals
Growing Basil
Growing Beans
Growing Berries
Growing Blueberries
Growing Cactus
Growing Corn
Growing Cotton
Growing Edibles
Growing Flowers
Growing Garlic
Growing Grapes
Growing Grass
Growing Herbs
Growing Jasmine
Growing Mint
Growing Mushrooms
Orchids
Growing Peanuts
Growing Perennials
Growing Plants
Growing Rosemary
Growing Roses
Growing Strawberries
Growing Sunflowers
Growing Thyme
Growing Tomatoes
Growing Tulips
Growing Vegetables
Herb Basics
Herb Garden
Indoor Growing
Landscaping Basics
Landscaping Patios
Landscaping Plants
Landscaping Shrubs
Landscaping Trees
Landscaping Walks & Pathways
Lawn Basics
Lawn Maintenance
Lawn Mowers
Lawn Ornaments
Lawn Planting
Lawn Tools
Outdoor Growing
Overall Landscape Planning
Pests, Weeds & Problems
Plant Basics
Rock Garden
Rose Garden
Shrubs
Soil
Specialty Gardens
Trees
Vegetable Garden
Yard Maintenance
How to Make a Seat for a Swing
How to Make a Seat for a Swing. How to Make a Seat for a Swing. You can buy a seat for a swing fairly easily, but manufactured swing seats lack the charm and individuality that a handmade seat provides. If you have a little woodworking skill, you can make your own seat for a swing quickly and easily.
How to Make a Seat for a Swing. You can buy a seat for a swing fairly easily, but manufactured swing seats lack the charm and individuality that a handmade seat provides. If you have a little woodworking skill, you can make your own seat for a swing quickly and easily.
Things You'll Need
Wood
Measuring tape
Saw
Sandpaper
Drill
Two 4-foot lengths of 3/8-inch nylon rope
Select the type of wood you want to use for your swing seat. You generally want strong, sturdy wood that can support whoever intends to use the swing. Redwood and cedar are the most highly recommended, but oak and pine are fairly reliable, too.
Measure the length of wood you want for your swing. Any swing seat should be at least 17 inches long by 8 inches wide by 1 inch deep. A deeper swing will be sturdier but can be more difficult to work with while you make it.
Compare the expected length of the swing with the placement of the chain, rope or supporting device you intend to use with it. You want the two lengths to be compatible, and may need to adjust the dimensions of the board slightly to fit.
Use a saw to cut the board until it fits the proper length for your seat.
Apply sandpaper to the wood until the splinters have been sanded out and the surface is smooth and comfortable.
Drill four holes into the wood, one in each corner. The holes should be equidistant from each other and approximately 3/8 inch in size. You'll be running rope through these to balance the swing, so you should measure the placement of the holes carefully.
Run each end of a 4-foot piece of nylon rope through the two right-side holes in the seat. Repeat the process with a second piece of nylon rope through the two left-side holes in the seat.
Measure the length you will need to hang the seat properly on the swing. It should be high enough off the ground so that whoever sits on it can just touch the ground with her toes.
Adjust the nylon rope to fit the length you require and tie the ends off with a thick knot. This will hold the rope in place on the seat.
Hang the seat on the swing.
Tips & Warnings
If you have access to a manufactured swing seat, you may want to use it as a blueprint for the one you make. It makes measuring easier, and if it comes from an existing swing set whose seat you are replacing with the handmade seat, you can be sure that the one you make will fit.
