Bulbs
Flower Basics
Flower Beds & Specialty Gardens
Flower Garden
Garden Furniture
Garden Gnomes
Garden Seeds
Garden Sheds
Garden Statues
Garden Tools & Supplies
Gardening Basics
Green & Organic
Groundcovers & Vines
Growing Annuals
Growing Basil
Growing Beans
Growing Berries
Growing Blueberries
Growing Cactus
Growing Corn
Growing Cotton
Growing Edibles
Growing Flowers
Growing Garlic
Growing Grapes
Growing Grass
Growing Herbs
Growing Jasmine
Growing Mint
Growing Mushrooms
Orchids
Growing Peanuts
Growing Perennials
Growing Plants
Growing Rosemary
Growing Roses
Growing Strawberries
Growing Sunflowers
Growing Thyme
Growing Tomatoes
Growing Tulips
Growing Vegetables
Herb Basics
Herb Garden
Indoor Growing
Landscaping Basics
Landscaping Patios
Landscaping Plants
Landscaping Shrubs
Landscaping Trees
Landscaping Walks & Pathways
Lawn Basics
Lawn Maintenance
Lawn Mowers
Lawn Ornaments
Lawn Planting
Lawn Tools
Outdoor Growing
Overall Landscape Planning
Pests, Weeds & Problems
Plant Basics
Rock Garden
Rose Garden
Shrubs
Soil
Specialty Gardens
Trees
Vegetable Garden
Yard Maintenance
How to Make a Wooden Weathervane
How to Make a Wooden Weathervane. The use of weathervanes, or wind vanes, goes back to early Mesopotamia. Writings unearthed in that area dated from 3,500 years ago mention a device used to determine the direction of the wind. Now we have far more sophisticated ways of predicting shifts in weather, but the weathervane is still a popular and useful...
The use of weathervanes, or wind vanes, goes back to early Mesopotamia. Writings unearthed in that area dated from 3,500 years ago mention a device used to determine the direction of the wind. Now we have far more sophisticated ways of predicting shifts in weather, but the weathervane is still a popular and useful decoration for many homes.
Things You'll Need
12-inch piece of 3/4-inch-by-3/4-inch square dowel
1/4-inch thick balsa wood or luan plywood, large enough to cut out two pieces approximately 4 inches square
Scroll saw
1-1/8-inch dowel
4-inch nail
Drill
3/16-inch drill bit
3D nail
Washer
Exterior paint or stain and varnish
Paintbrush
Hammer
Glue
Sandpaper
Sketch a equilateral triangle with four-inch sides on the balsa or luan for the head of your weathervane's arrow.
Sketch a trapezoid with the shortest side being 3 inches and the longest 5 inches for the tail of the arrow.
Using the scroll saw, cut out the shapes you just drew.
Sand the edges of the balsa shapes with the sandpaper. Sand the triangle on its flat sides as well to reduce its width slightly.
Using the scroll saw, cut a slit ? inch deep into each end of the square dowel. Make it wide enough to insert wood shapes.
Drill a hole in the center of the square dowel. The hole should be slightly larger than your 3D nail, but not large enough for the head of the nail to slip through.
Glue the shapes into the slits in the wooden dowel. Allow to dry.
Paint or stain and varnish the weathervane to seal the wood for outdoor use. Be sure the pivot hole stays clear. If you want, you can also paint the 1-1/8-inch dowel (which will be used for mounting).
Put the washer on the end of the 1?-inch dowel and hammer the 3D nail through the hole in the arm of the weathervane into the end of the round dowel. Leave approximately 1/16 inch of clearance between the head of the nail and the top of the square dowel.
Mount your weathervane outside and enjoy.
Tips & Warnings
The trick to balancing your weathervane properly is to have unequal area, but equal mass on either side of your pivot point. (That's why you sanded the triangle point of your arrow.)
Your weathervane will point into the wind, showing you the direction the wind is coming from.
