Bulbs Flower Basics Flower Beds & Specialty Gardens Flower Garden Garden Furniture Garden Gnomes Garden Seeds Garden Sheds Garden Statues Garden Tools & Supplies Gardening Basics Green & Organic Groundcovers & Vines Growing Annuals Growing Basil Growing Beans Growing Berries Growing Blueberries Growing Cactus Growing Corn Growing Cotton Growing Edibles Growing Flowers Growing Garlic Growing Grapes Growing Grass Growing Herbs Growing Jasmine Growing Mint Growing Mushrooms Orchids Growing Peanuts Growing Perennials Growing Plants Growing Rosemary Growing Roses Growing Strawberries Growing Sunflowers Growing Thyme Growing Tomatoes Growing Tulips Growing Vegetables Herb Basics Herb Garden Indoor Growing Landscaping Basics Landscaping Patios Landscaping Plants Landscaping Shrubs Landscaping Trees Landscaping Walks & Pathways Lawn Basics Lawn Maintenance Lawn Mowers Lawn Ornaments Lawn Planting Lawn Tools Outdoor Growing Overall Landscape Planning Pests, Weeds & Problems Plant Basics Rock Garden Rose Garden Shrubs Soil Specialty Gardens Trees Vegetable Garden Yard Maintenance

How to Make Potato Dextrose Agar

How to Start Lemon Seeds Indoors - watch on youtube
How to Make Potato Dextrose Agar

How to Make Potato Dextrose Agar. Potato dextrose agar (PDA) is a good general-purpose semisolid medium used for culturing fungi. It is often used to isolate, grow and maintain mushroom-forming species. Ready-made petri dishes or test tubes containing PDA can be purchased, or PDA can be quickly made using a commercial premix. However, it is not...

Potato dextrose agar (PDA) is a good general-purpose semisolid medium used for culturing fungi. It is often used to isolate, grow and maintain mushroom-forming species. Ready-made petri dishes or test tubes containing PDA can be purchased, or PDA can be quickly made using a commercial premix. However, it is not hard to make a simple and effective version from scratch at little cost.
Things You'll Need
300 g peeled, chopped potatoes
Saucepan
Kitchen strainer or cheesecloth
pH test paper or pH meter
1 molar hydrochloric acid
1 molar sodium hydroxide
4 500-mL glass Ehrlenmayer flasks (or other narrow-mouthed autoclavable containers)
10 g dextrose (glucose) powder
20 g agar
Aluminum foil
Pressure cooker
Sterile petri dishes
Preparing Potato Extract
Place potatoes in a saucepan with approximately 1.2 liters of tap water and boil on a stove for 1 hour.
Remove saucepan from heat and let liquid cool until it can be comfortably handled (about 10 minutes).
Pour liquid potato extract through a strainer or cheesecloth and collect it in another container.
Preparing the Medium
Add dextrose and agar to 1 liter of the potato extract water.
Test the pH of the solution with pH test paper or a pH meter.
If the pH is above 6.5, adjust it down by adding one drop of the hydrochloric acid solution at a time and retesting.
If the pH is below 6, adjust it up by adding one drop of the sodium hydroxide solution at a time and retesting.
Sterilization
Thoroughly mix the medium and divide it into smaller batches of 250 mL poured into the four 500-mL flasks (Note: each flask must be no more than half full to avoid boil over).
Cover each flask with a piece of loosely crimped aluminum foil, so the foil will not fall off, but does not make a tight seal.
Place the flasks in a pressure cooker.
Operate the pressure cooker in accordance with the manufacturer's instructions to sterilize the PDA at 121 degrees C (250 degrees F) at a pressure of 103,421 Pascals(15 PSI) for 15 minutes.
Shut off the pressure cooker and let it return to atmospheric pressure, then remove the flasks and let them cool until they can be handled.
Pouring the Medium
Line up the sterile petri dishes on a flat surface.
Once the flasks have cooled to handling temperature, but before the medium begins to solidify, grasp a flask with one hand and remove and set aside its foil lid with the other hand.
For each petri dish, lift the lid with one hand, quickly fill halfway with liquid PDA, and replace the lid.
Repeat Step 3 above until all petri dished are filled.
If there is any PDA left over, loosely recover the flask with its original foil lid, let it cool and solidify, tighten the foil lid and store in a refrigerator.

Check out these related posts