Bulbs
Flower Basics
Flower Beds & Specialty Gardens
Flower Garden
Garden Furniture
Garden Gnomes
Garden Seeds
Garden Sheds
Garden Statues
Garden Tools & Supplies
Gardening Basics
Green & Organic
Groundcovers & Vines
Growing Annuals
Growing Basil
Growing Beans
Growing Berries
Growing Blueberries
Growing Cactus
Growing Corn
Growing Cotton
Growing Edibles
Growing Flowers
Growing Garlic
Growing Grapes
Growing Grass
Growing Herbs
Growing Jasmine
Growing Mint
Growing Mushrooms
Orchids
Growing Peanuts
Growing Perennials
Growing Plants
Growing Rosemary
Growing Roses
Growing Strawberries
Growing Sunflowers
Growing Thyme
Growing Tomatoes
Growing Tulips
Growing Vegetables
Herb Basics
Herb Garden
Indoor Growing
Landscaping Basics
Landscaping Patios
Landscaping Plants
Landscaping Shrubs
Landscaping Trees
Landscaping Walks & Pathways
Lawn Basics
Lawn Maintenance
Lawn Mowers
Lawn Ornaments
Lawn Planting
Lawn Tools
Outdoor Growing
Overall Landscape Planning
Pests, Weeds & Problems
Plant Basics
Rock Garden
Rose Garden
Shrubs
Soil
Specialty Gardens
Trees
Vegetable Garden
Yard Maintenance
How to Troubleshoot a Snapper Riding Mower That Will Not Start
How to Troubleshoot a Snapper Riding Mower That Will Not Start. Snapper riding mowers use Briggs & Stratton engines, which are typically very easy for the novice to repair. All engines, and especially small engines, require three things to run properly if they are electric start: spark, gas, air and a charged battery. Troubleshooting and fixing...
Snapper riding mowers use Briggs & Stratton engines, which are typically very easy for the novice to repair. All engines, and especially small engines, require three things to run properly if they are electric start: spark, gas, air and a charged battery. Troubleshooting and fixing your Snapper riding mower at home will save you the large mechanic bill and will require a few common tools, as well as a battery tester and charger.
Things You'll Need
Battery tester
6 volt battery charger
Flathead screwdriver
Carb cleaner
Air filter
Socket wrench and ratchet
Foot-pound torque wrench
Spark plug
Turn on the battery tester. Switch it to the 6-volt setting, as small engines use 6-volt batteries. Flip up the seat on the mower to expose the battery located below the seat. Touch the red probe on the tester to the positive post on the battery. Touch the black probe on the tester to the negative post on the battery. The meter should read between 5 to 6 volts. If it doesn't, then you will need to charge the battery with a 6-volt battery charger.
Unscrew the gas tank cap and make sure there is fuel in the tank. If so, follow the fuel line from the gas tank to the side of the carburetor. Squeeze the spring-loaded clamp holding the hose onto the carburetor with the pliers and slide it off the hose. Pull the gas hose off and point it into the gas tank.
Spray carb cleaner into the side of the carburetor. Unscrew the bolt from the base of the carburetor and pull off the fuel bowl. Dump out all the gummy gas in the fuel bowl. Spray carb cleaner into the fuel bowl and onto the float above the bowl. Tighten the fuel bowl back on and clamp the gas hose back onto the carburetor. Cleaning the carburetor should be done if the engine sounded like it was dying or like it needed gas while it was still running.
Unscrew the wingnut holding the cover over the air filter on top of the engine. Pull the cover off and inspect the air filter. If the air filter is dirty or oily, then the engine isn't getting the proper amount of air to mix with the fuel for injection and won't start. Replace the air filter if it is dirty. Tighten the cover back over the air filter.
Pull the cap off of the spark plug on the front of the engine. Unscrew the spark plug with the correct sized socket. Inspect the spark plug. If the gap at the end of the spark plug is filled with oil and grease then the engine won't start because there is no spark. Tighten a new spark plug in with your fingers. Fit the socket onto the foot-pound torque wrench and tighten the spark plug in until the torque wrench meter reads 15 ft-lbs. Replace the spark plug cap.
