Bulbs
Flower Basics
Flower Beds & Specialty Gardens
Flower Garden
Garden Furniture
Garden Gnomes
Garden Seeds
Garden Sheds
Garden Statues
Garden Tools & Supplies
Gardening Basics
Green & Organic
Groundcovers & Vines
Growing Annuals
Growing Basil
Growing Beans
Growing Berries
Growing Blueberries
Growing Cactus
Growing Corn
Growing Cotton
Growing Edibles
Growing Flowers
Growing Garlic
Growing Grapes
Growing Grass
Growing Herbs
Growing Jasmine
Growing Mint
Growing Mushrooms
Orchids
Growing Peanuts
Growing Perennials
Growing Plants
Growing Rosemary
Growing Roses
Growing Strawberries
Growing Sunflowers
Growing Thyme
Growing Tomatoes
Growing Tulips
Growing Vegetables
Herb Basics
Herb Garden
Indoor Growing
Landscaping Basics
Landscaping Patios
Landscaping Plants
Landscaping Shrubs
Landscaping Trees
Landscaping Walks & Pathways
Lawn Basics
Lawn Maintenance
Lawn Mowers
Lawn Ornaments
Lawn Planting
Lawn Tools
Outdoor Growing
Overall Landscape Planning
Pests, Weeds & Problems
Plant Basics
Rock Garden
Rose Garden
Shrubs
Soil
Specialty Gardens
Trees
Vegetable Garden
Yard Maintenance
How to Troubleshoot a Kohler Fuel Solenoid
How to Troubleshoot a Kohler Fuel Solenoid. Backfiring is a startling explosive sound that can happen when you shut down your lawn mower or other small-engine-powered equipment. Fuel shutoff solenoids prevent engines, including the Kohler brand, from backfiring. By effectively blocking fuel flow to the carburetor when the ignition key switches to...
Backfiring is a startling explosive sound that can happen when you shut down your lawn mower or other small-engine-powered equipment. Fuel shutoff solenoids prevent engines, including the Kohler brand, from backfiring. By effectively blocking fuel flow to the carburetor when the ignition key switches to the "Off" position, excess fuel can't enter the combustion chamber, eliminating the potential for that annoying noise. If backfire still occurs, the fuel shutoff solenoid is suspect and requires investigation.
Things You'll Need
Volt-Ohm meter
Lower the throttle to the mid-range position just before shutting the Kohler engine down. In order for the fuel shutoff valve to work properly, the throttle position should be in the full to mid-range position. If a backfire occurs despite following the proper shutdown procedures, check for proper voltage.
Test for a minimum of 7 Volts DC at the fuel solenoid terminal using a Volt-Ohm meter. Place one of the meter leads to the solenoids terminal, and the second lead to the engine case. Power from the battery shuts the fuel flow off to the carburetor. No power is present on the solenoid while the engine is running. If no (or low) voltage is present at the solenoid, check the battery for proper charge and for good battery connection.
Test the battery for voltage using the Volt-Ohm meter. Attach the Volt-Ohm meter across the positive and negative battery posts while the engine is shut down. Crank the engine and observe the voltage drop across the battery posts. If the voltage drops below 9 Volts DC, apply a battery charger and bring the battery back to its appropriate charge. Replace the battery if it will not accept a charge.
Remove the fuel shutoff solenoid from the carburetor for further testing if the above tests reveal no problems. Connect 12 Volts DC power to the solenoid. Connect the negative (ground) lead to the solenoid case, and apply the positive (red) lead to the solenoid terminal. If the solenoid does not shift to the "Off" position, the solenoid is bad and replacement is necessary.
Tips & Warnings
Check the fuel supply and fuel filter if engine fails to start before troubleshooting the fuel shutoff solenoid.
Use extreme caution when working around fuel and a battery source--even a small spark will ignite the fuel.
