Bulbs
Flower Basics
Flower Beds & Specialty Gardens
Flower Garden
Garden Furniture
Garden Gnomes
Garden Seeds
Garden Sheds
Garden Statues
Garden Tools & Supplies
Gardening Basics
Green & Organic
Groundcovers & Vines
Growing Annuals
Growing Basil
Growing Beans
Growing Berries
Growing Blueberries
Growing Cactus
Growing Corn
Growing Cotton
Growing Edibles
Growing Flowers
Growing Garlic
Growing Grapes
Growing Grass
Growing Herbs
Growing Jasmine
Growing Mint
Growing Mushrooms
Orchids
Growing Peanuts
Growing Perennials
Growing Plants
Growing Rosemary
Growing Roses
Growing Strawberries
Growing Sunflowers
Growing Thyme
Growing Tomatoes
Growing Tulips
Growing Vegetables
Herb Basics
Herb Garden
Indoor Growing
Landscaping Basics
Landscaping Patios
Landscaping Plants
Landscaping Shrubs
Landscaping Trees
Landscaping Walks & Pathways
Lawn Basics
Lawn Maintenance
Lawn Mowers
Lawn Ornaments
Lawn Planting
Lawn Tools
Outdoor Growing
Overall Landscape Planning
Pests, Weeds & Problems
Plant Basics
Rock Garden
Rose Garden
Shrubs
Soil
Specialty Gardens
Trees
Vegetable Garden
Yard Maintenance
How to Make a Sand Mold for Concrete
How to Make a Sand Mold for Concrete. Creating a sand mold for concrete is a quick and inexpensive method of reproducing ornamental objects in concrete form. The process uses fine wet sand to hold the image of the casting model. The sand is just strong enough to avoid crumbling as you pour concrete into the depression left by the mold. After a...
Creating a sand mold for concrete is a quick and inexpensive method of reproducing ornamental objects in concrete form. The process uses fine wet sand to hold the image of the casting model. The sand is just strong enough to avoid crumbling as you pour concrete into the depression left by the mold. After a short wait for the concrete to harden, you can pull the cast replica of your modeled object free and enjoy a beautifully cast concrete ornament suitable for display.
Things You'll Need
Plywood
Table saw
Wood screws
Screwdriver
Fine mason's sand
Water
Spray bottle
Model
Bucket
Electric drill with paddle bit
Concrete mix
3/4-inch plywood
Create a box form large enough to hold the cast. Build a box using 3/4-inch plywood as the base and sides. Use a table saw to cut the plywood to the dimensions needed, allowing about 4 extra inches to the width, length and depth of the box to allow space for the sand to shift when imprinted with the model. Join the box sides with wood screws.
Fill the box to the top using fine mason's sand. The finer the sand used the greater the detail you'll get in the mold to carry over to the concrete.
Dampen the sand with water to make it moldable.
Press the model of the object that you wish to reproduce into the wet sand, dislodging the sand in the process. Pull the model carefully from the sand, straight up to disturb as little of the sand as possible, leaving an imprint of the model behind as a sand mold.
Repair any parts of the imprint that crumbles with your fingers or with a small putty knife. Moisten the sand occasionally with a spray bottle filled with water to keep the mold fresh.
Attach a paddle but to an electric drill and use the paddle to mix the concrete mix with water in a bucket. Create a smooth, pourable mix, about the same consistency as oatmeal.
Pour the concrete into the mold, filling the imprint completely. Wait for the concrete to set. Setting times depend on the concrete used, check the manufacturer's instructions for the time required.
Pull the concrete from the mold and brush off any clinging sand. You should have an object the same shape and size as the model.
Tips & Warnings
Use paver sand that hardens when wet to create a mold that holds greater details. However, first spray the mold with mold release agent before pressing into the sand to prevent sand sticking to its surface.
