Bulbs
Flower Basics
Flower Beds & Specialty Gardens
Flower Garden
Garden Furniture
Garden Gnomes
Garden Seeds
Garden Sheds
Garden Statues
Garden Tools & Supplies
Gardening Basics
Green & Organic
Groundcovers & Vines
Growing Annuals
Growing Basil
Growing Beans
Growing Berries
Growing Blueberries
Growing Cactus
Growing Corn
Growing Cotton
Growing Edibles
Growing Flowers
Growing Garlic
Growing Grapes
Growing Grass
Growing Herbs
Growing Jasmine
Growing Mint
Growing Mushrooms
Orchids
Growing Peanuts
Growing Perennials
Growing Plants
Growing Rosemary
Growing Roses
Growing Strawberries
Growing Sunflowers
Growing Thyme
Growing Tomatoes
Growing Tulips
Growing Vegetables
Herb Basics
Herb Garden
Indoor Growing
Landscaping Basics
Landscaping Patios
Landscaping Plants
Landscaping Shrubs
Landscaping Trees
Landscaping Walks & Pathways
Lawn Basics
Lawn Maintenance
Lawn Mowers
Lawn Ornaments
Lawn Planting
Lawn Tools
Outdoor Growing
Overall Landscape Planning
Pests, Weeds & Problems
Plant Basics
Rock Garden
Rose Garden
Shrubs
Soil
Specialty Gardens
Trees
Vegetable Garden
Yard Maintenance
How to Cut Out an Eaves Trough Folding Downspout
How to Cut Out an Eaves Trough Folding Downspout. The downspout on a home's eaves trough system often gets in the way when performing yard and lawn maintenance. The downspout carries water down the side of the home. The metal tube turns out into the yard to carry rain runoff away from the home so the water doesn't settle around the home's...
The downspout on a home's eaves trough system often gets in the way when performing yard and lawn maintenance. The downspout carries water down the side of the home. The metal tube turns out into the yard to carry rain runoff away from the home so the water doesn't settle around the home's foundation. The downspout turnout can be 48 to 60 inches long, and as a result is an obstacle when mowing or trimming the landscaping near the home. A simple trick can turn this fixed obstacle into a movable downspout.
Things You'll Need
Downspout elbow
48-inch section of downspout
Tin snips for aluminum downspouts
Jig saw for plastic PVC downspout
Pop rivet gun and 1/8-inch pop rivets
Cordless drill with 1/8-inch drill bit
Test fit the downspout elbow to the bottom of the downspout. The downspout elbow should be approximately 12 inches above grade level.
Bend the free end of the elbow outward a bit, so that the downspout fits into the elbow rather than around the outside of the elbow. If you are working with plastic systems, the elbows are already designed this way. If you are working with aluminum downspouts, the elbow is crimped and can be easily bent outward and made large enough to fit around the outside of the downspout.
Cut inward from the end of the elbow toward the elbow bend using tin snips. Make a cut 2 1/2 inches long. Make this same cut on both sides of the elbow, cutting a straight line that is along the center line of the elbow. At 2 1/2 inches in from the end of the elbow, cut upward over the top of the elbow. The result is that you will remove a section from the top of the elbow that is 2 1/2 inches long and as wide as the entire width of the elbow.
Set the 48-inch piece of downspout into the saddle created by removing the top of the elbow. Push the downspout so that it is inserted past the cut line and into the elbow not more than 1/2 inch.
Drill a 1/8-inch hole on each side of the elbow, through both the elbow and the downspout. Fasten the two together with a single pop rivet on each side of the elbow. The pop rivets will act as a pivot hinge. With the top of the elbow removed, the 48-inch section of downspout will lift upward and out of the way when you need to mow the grass under the spout.
