Bulbs
Flower Basics
Flower Beds & Specialty Gardens
Flower Garden
Garden Furniture
Garden Gnomes
Garden Seeds
Garden Sheds
Garden Statues
Garden Tools & Supplies
Gardening Basics
Green & Organic
Groundcovers & Vines
Growing Annuals
Growing Basil
Growing Beans
Growing Berries
Growing Blueberries
Growing Cactus
Growing Corn
Growing Cotton
Growing Edibles
Growing Flowers
Growing Garlic
Growing Grapes
Growing Grass
Growing Herbs
Growing Jasmine
Growing Mint
Growing Mushrooms
Orchids
Growing Peanuts
Growing Perennials
Growing Plants
Growing Rosemary
Growing Roses
Growing Strawberries
Growing Sunflowers
Growing Thyme
Growing Tomatoes
Growing Tulips
Growing Vegetables
Herb Basics
Herb Garden
Indoor Growing
Landscaping Basics
Landscaping Patios
Landscaping Plants
Landscaping Shrubs
Landscaping Trees
Landscaping Walks & Pathways
Lawn Basics
Lawn Maintenance
Lawn Mowers
Lawn Ornaments
Lawn Planting
Lawn Tools
Outdoor Growing
Overall Landscape Planning
Pests, Weeds & Problems
Plant Basics
Rock Garden
Rose Garden
Shrubs
Soil
Specialty Gardens
Trees
Vegetable Garden
Yard Maintenance
How to Rebuild a Stihl Carburetor
How to Rebuild a Stihl Carburetor. The carburetors used almost every Stihl power tool is called an all position diaphragm with integrated fuel pump. The purpose of the carburetor is to mix air and fuel before it’s ignited in the chamber. There are three sections to these carburetors: a metering section, where gas and air are measured; a...
The carburetors used almost every Stihl power tool is called an all position diaphragm with integrated fuel pump. The purpose of the carburetor is to mix air and fuel before it’s ignited in the chamber. There are three sections to these carburetors: a metering section, where gas and air are measured; a mixing section, where the two are blended before ignition; and a pumping section, where the mixed fuel is sent to the cylinder. Rebuilding these carburetors takes extreme caution--the small parts are easily damaged.
Things You'll Need
Small screwdriver
Screwdriver
Needle nosed pliers
Toothpick
Pressure gauge
Start rebuilding the carburetor on the fuel metering section. Screw the high speed and low speed fuel mixture screws, with new rubber seals, into their holes, using the small screwdriver. Tighten them until they are fully seated.
Fit the inlet needle onto the carburetor body using the needle nosed pliers. Set the spring into its hole just before the inlet needle with the needle nosed pliers. Push the spindle through the circular hole on the inlet control lever. Using the needle nosed pliers, engage the control lever’s clevis with the head of the inlet needle.
Press the inlet control lever down and tighten it in place with the screw, using the screwdriver. Test the inlet control lever by pushing it down lightly, to make sure it engages the inlet needle. Make sure the top end of the inlet control lever is flush with the bottom of the metering chamber floor. If the lever isn’t flush, it is bent and must be replaced.
Set the metering section’s gasket on top of the carburetor’s body. Place the fuel metering diaphragm on top of the gasket. Push the pegs in place with the butt of the screwdriver to secure the diaphragm and gasket in place. Place the metering cover, positioned with the ventilation hole toward the cylinder, over the diaphragm. Screw the cover in place with the screwdriver.
Press the fuel inlet screen into the fuel inlet valve using the toothpick; make sure it is flat and even. Place the pump’s diaphragm against the carburetor body. Set the pump’s gasket on top of the diaphragm. Tighten the cover’s screws, using the screwdriver, in place over the gasket and diaphragm.
Pressure test the carburetor after it’s assembled. Place the hose of the pressure gauge into the fuel inlet valve. Submerge the carburetor into a container of fuel. Pump the pressure to 11.6 psi. The carburetor shouldn’t leak any air and the pressure should remain constant. If the pressure drops, it is likely due to an improperly seated inlet needle or a warped diaphragm. Replace parts as necessary.
